Zuhause> Produkt-Liste> Horizontale Aufschlämmpumpe> ZJW-Förderpumpen> Förderpumpen für Mühlenmahlen
Förderpumpen für Mühlenmahlen
Förderpumpen für Mühlenmahlen
Förderpumpen für Mühlenmahlen
Förderpumpen für Mühlenmahlen
Förderpumpen für Mühlenmahlen
Förderpumpen für Mühlenmahlen

Förderpumpen für Mühlenmahlen

$5000≥1Set/Sets

Zahlungsart:L/C,T/T,Paypal,Money Gram,Western Union
Incoterm:FOB,CFR,CIF,EXW,FAS,FCA,CPT,CIP,Express Delivery
Minimum der Bestellmenge:1 Set/Sets
Transport:Ocean,Land,Air,Express,Express
Hafen:Tianjin,Qingdao,Guangzhou
Produkteigenschaften

Modell65ZJW

MarkeNaipu

TypeClay Wet Sand

Casting MethodThermal Gravity Casting

Sand Core TypeClay Sand Core

ApplicationMachinery Parts

MachiningBoring Machine

MaterialSteel

Surface TreatmentSand Blast

Surface RoughnessRa0.4

StandardGB

CertificationISO 9001:2008

65ZJW Feeding Pumps65

Verpackung & Lieferung
Verkaufseinheiten : Set/Sets
Pakettyp : Holzkiste
Bildbeispiel :
Produktbeschreibung

65 zjw Filterpresse Förderpumpen

Freitragende horizontale Schlammkreiselpumpen/Güllepumpen mit Gummiauskleidung/R55 Schlammpumpen/Güllepumpen mit Stopfbuchsdichtung/Schlammpumpen mit Zentrifugaldichtung/Schlammpumpen aus verschleißfestem Gummi/auswechselbare Schlammpumpen/Kohlewaschschlammpumpen/Güllepumpen zur Sand- und Kiesförderung/Gülleförderpumpen für Abwasser Pumpen /Flotationspumpen für Mineralien/Kohlewaschpumpen/Förderpumpen


Die Naipu® NP-ZJW- Serie Filterpresse -Zuführpumpe akzeptiert eine einzigartige hydraulische Konstruktion und Installationsart des

Laufrad, stellen Sie sicher, dass seine Pumpenleistungskurve steiler ist als bei normalen Pumpen, ist besser für den Einsatz in der

Die Zufuhr der Filterpresse variiert je nach Widerstandsänderung, um die große Kapazität zu realisieren,

Niederdruckzufuhr und niedrige Kapazität, Hochdruckfilter. Die Pumpe ist in der Kohlewäsche weit verbreitet,

Umweltschutz, Aluminiumfabrik, Schmelzwerk usw.



Konstruktionszeichnung

drawing-1





Das Strukturdiagramm der Förderpumpe

1.Zweiphasenspirale 2.Zweiphasenlaufrad

3.Einphasige Spirale 4.Rückplatte

5.Fütterungsraum 6.Lokalisierung des Busches

7.Expeller 8.Expeller Abdeckplatte

9.Dekompressionskörper 10.Einphasiges Laufrad

11.Traverse 12.Wellenhülse

13.Abdeckplatte 14.Demontagering

15.Wasserhalteplatte 16.Lager

17.Welle 18.Lagerdistanzhülse

19.Lagerdeckel 20.Rahmen

21.Gebogenes Rohr



AUSWAHLTABELLE NP-ZJW-PUMPE

selection chart



NP-ZJW LEISTUNGSPARAMETER DER FÜHRUNGSPUMPE

Performance Parameters


Produktübersichten:

Filter Press Photos


Mögliche Fehler und Setzungen.


        Faults

    Reason

      Settlement

1.Pump fails to discharge any water,The hand of pressure gauge beat violently

1.Suction pipe don`t have enough water.

2.Suction pipe blocked or the valve is locked.

1. Inject enough water

2.unlock the inlet valve,clear the blocks

3.Exclude the air leakage

2.The pump can`t discharge water,the hand of vacuum meter beat heavily.

1.The inlet valve is unlocked or silted up.

2.The resistance of suction pipe is too big or silted up.

3.The height of suction is too high.

1.Unlock the valve or desilting

2.improve the design of  suction pipe or desilt

3.Lower the height of the installation.

3.The pump can`t discharge water,pressure gauge shows heavy pressure.

1.The resistance of the discharge pipe is too big.

2.The impeller blocked

3.The speed is slow.

1.Check and adjust the outlet pipe.

2.Clear the impeller

3. Improve the speed.

4.The pump doesn`t rotate

The volute is silted up by the blocks.

Clear the blocks

5.The capacity is not enough

1.The blocks of the impeller or the inlet or outlet pipe.

2.The abrasion of the impeller is heavily.

3.The speed is low to normal

4.Pump is installed unreasonably or the leakage of the inlet pipe.

5.The transporting height is too high,the loss of the resistance of the inside pipe are too big.

6.The inlet valve not open enough or blocked

7.The packing seal leaks

1.Clear the impeller or pipe.

2.Change the impeller

 

 

3.Adjust the speed

4.Install again or stop leaking.

 

 

5.Decrease the height of the transport or reduce the resistance.

6.Unlock the inlet valve

 

7.Compress the packing tightly

6.The motor of the pump is overloaded

1.The head of the pump exceeds the head of the working condition.

2.Not consider the slurry density when selecting the pump.

3.The packing press tightly

1.Turn down the outlet valve,cut the impeller or lower the speed.

2.Select the motor again.

3.Adjust the the screw of the  packing gland

7.Abnormal sound in the pump, and no water out

1.The resistance of the inlet pipe is too big.

2.The height of the suction is too high.

3.Cavitation occurred

4.there is air in the inlet

5.The temperature of the liquid is too high

1.Clear the suction pipe and sluice valve.

2.Lower the height of the suction

3.Adjust the water valve and let the pump operate in the defined limits.

4.Block the leakage.

5.Lowering the liquid temperature.

8.pump vibrates

1.pump cavitate

2.The block of the impeller single vane

3.The no concentricity  between the pump shaft and motor shaft

4.Fasteners or foundation loose

1.Adjust the water valve ,lower the height of the installation,reduce the resistance of the inlet.

2.Clear the impeller

3.Alignment again

4.Fasten the screw,and reinforce the foundation.

9.Bearing is overheat

1.lock the cooling water

2.lubrication is not good.

3.the lubrication oil is not clear

4.the wrong direction of the thrust bearing.

5.there is something wrong with the bearing.

1.Open the cooling water

2.Adjust the oil quantity

3.Clear the shaft,change oil

4.According to the inlet pressure,adjust the direction of the thrust bearing.

5.Change the bearing

10.Packing short life

The material of packing is not good

Change the packing

11.pump leak oil

1.High oil level

2.The rubber parts invalid  

3.Assembly problem

1.Lower the oil level

2.Change rubber spares

3.Adjust the assembly

 

12 Pump head leaking

1.The rubber parts not press well

Assembly again or press tightly 





FAQ:

Q1. Sind Sie eine Herstellerfabrik?

Ja, wir sind die direkte Manufakturfabrik und haben mehr als 10 Jahre Erfahrung in diesem Bereich.

Q2.Haben Sie Lagerprodukte zu verkaufen?

Einige haben wir auf Lager, andere nicht. Da wir diese Produkte immer nach Kundenwunsch produzieren.

Q3.Welche Vorteile haben Sie?

A: Wir sind direkter Hersteller und der Preis ist wettbewerbsfähig.

B: Unser Ingenieur ist in diesem Bereich sehr erfahren und wir können Ihnen OEM-Service anbieten.

C: Wir sind Fabrik und wir können einen Produktionsplan arrangieren, um eine pünktliche Lieferung zu gewährleisten.


Kontaktdetails:

Shijiazhuang Naipu Pump Co., Ltd.

Hinzufügen: No.368 Xinshi North Road, Shijiazhuang Hi-Tech Industry Development Zone, Hebei, China, 050091.

Tel: 0086-311-897162903

Fax:0086-311-87162902

Ansprechpartner: Karen Tan

Skype: karen_naipump











  • Anfrage versenden

Copyright ©2024 Shijiazhuang Naipu Pump Co., Ltd.Alle Rechte vorbehalten

Anfrage versenden
*
*

We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

senden